Search the Community
Showing results for tags 'r200'.
Found 8 results
-
I'm new to the forum but wanted to share some pics of the rod holders I added to my 2016 R200. I was lacking some in the transom area for trolling. I used small aluminum strips for backing plates. Look pretty good. It was a bit scary cutting 2" holes in my boat.
-
Just bought an Etec 200hp to replace the 130 hp Yammie that was on my R200. The Etec is almost 200 lbs heavier than the old motor so I'm looking for prop suggestions that will give me some stern lift. I'm willing to listen to all points of view and not specifically BRP products. Thanks in advance
-
OK folks, I haven't even pulled the boat out of the water yet (planned for 8/13) but I've already started to prototype a new console for her. I did the prototype with foam. The actual console will be cored with 1/2" marine plywood with 2 layers of 1708 inside and 3 layers outside. First pic: Batteries will be under seat. Second pic: Steering will be on lower vertical surface (it's where I prefer it), engine controls and switch panel on the sloping surface, electronics bay on top. Lower right side will have storage. Last pic: profile view from left side I'd appreciate any comments on the concept including design flaws. Larry (I'll keep the pics coming as this project develops)
-
I bought a used 2007 Etec 200 HO to repower my 1975 Robalo R200 and have no idea where to start as far as prop for this setup. This is a very heavy hull so I'm thinking a 4 bladed prop will be needed. The setup is also stern heavy due to 200+ lbs of additional weight over the 130 Yamaha (way underpowered) that was on it. I've already planned on moving the 3 batteries to the console to help re-balance the boat. Anyone have suggestions on where to start as far as testing props for this setup?
-
I have a 2016 R200 and want to find a fiberglass tackle box to install where the removable cooler is (under the bolster seats). Does anyone have any info on one or already completed the mod? Thanks in advance.
-
Just bought a dual torsion axle BoatMaster trailer to haul the boat with. It has fixed, 2x12, upright bunks (2" edge up) that are 64" apart. Should I replace the bunks with adjustable ones? If so, I need to know how far off the center-line of the trailer they should be and at what angle in relation to the trailer.
-
Can anyone help me out? I'm planning on replacing the gas tank on my 1975 R200 next off-season and would like to order the tank in advance of the work starting but I need dimensions. I also need recommendations concerning the order of work because I'll also be replacing the transom. Should I do the tank before the transom? All work will be done while the boat is on it's trailer. Thanks in advance.
-
Up for sale 1977 R200 Restored 2012 F150 Yamaha . 175 hours I bought this boat shortly after it had been painted with just a t-top here is what as been done and added, all done from 2012-2014 new Awl grip paint not perfect small imperfections full transom added porta bracket new f150 Yamaha 4 stroke brand new 2012 "I average on about every fill up 2.75-3.5 gph" completely rewired 2 clarion 10" subs 150 watt amp 2 8" lawrance speakers clarion am/fm aux cd radio vhf radio 45 gallon lean to live well plumbed the correct way 1100gph rear under back deck turned into bildge are with 2 bildge pumps both with auto feb 2014 sea dek on entire boat t top with electronic box 4 rocket launchers teak redone feb 2014 not perfect boat is old and all original push pole " yes I push this boat " we fish deep in the mangroves 1-2 miles back front of console turned into insulated cooler cushions complete front deck, center console seal , lean post seat seastar stearing tilt wheel dual batteries in console Im sure there is something im missing , we use this boat a lot didn't build it to sit , it is kept under a pole barn since I had it done. This is the second motor I have had on it so I have put about 200+ hours on it since done . The boat easily will run with porta bracket in 12" of water . floats in about 14" , with a 4 blade prop take off in 2' currently in 3-4' . Top speed 45 with current prop. I built this boat to have around for a while I believe I am the 3 owner the guy I bought it from had it for 16 years, how ever I am planning on getting into guiding and looking for a tower boat. Please if you have any questions please ask , only thing the boat could use is gps/depth finder they both took a dump on me this year both lowrance dash mounted, and the trailer needs a rebuild I only go 6 miles each way to the water so I haven't bothered. Price $28500 obo
